Finishing the aft deck consisted painting the swim platform, painting the hand rails on the swim platform, painting the transom, painting the aft deck and aft deck bulwark, hanging the two bulwark doors on the aft deck and installing the wood cap on the aft deck bulwark.
By the time I fabricated the jamb and the stainless steel keepers,t he two bulwark doors took almost a day to hang. I built these two door handles a little different than the Portuguese bridge door handle, and they were much more simple to install. I had allowed these handles to project more in to the deck area so I had more meat on the jamb, which let me do the installation without mortising the jamb. Im totally happy with how tight the door closes and how the handles look. Im glad I went the extra effort with this style vs going to a big box store and using an off the shelf gate latch. There are two doors on the aft deck. If we are tied to a dock on the starboard side, well step up and enter the boat via the starboard door. If we are tied off on the port side, well step on the the swim platform and step up the aft deck using the transom steps. 
Painting the transom and the swim platform gave me a chance to see the green color on the boat and how the green looks next to the off white. Like the fore deck hand rails, I decided to paint the hand rails on the swim platform. The hand rails on the swim platform were made of 1 1/2" 316 stainless schedule 40 pipe,
but I did not want trust my ability to polish them bright, and felt paint would be the most maintenance free treatment. I really like the look of bright stainless, but I doubted I could prevent them from rusting. I also painted the stainless steps going from the swim platform to the aft deck. Like the rest of the swim platform and decks, Ill add anti skid once she ready for launch and I"m not dealing with mud being tracked on deck. I like the green chosen for the hull color but it makes the off white look more like pure white when the two are next to each other. For a comparison look at the off white next to the pure white I painted on the wheel house floor as compared to the off white next to the green. I was afraid to go much darker on the off white for fear of heating the decks up to much.
Ive increased the size of the aft deck which decreases the size of the salon. Having the covered aft deck large enough for a table and four chairs was more important to me than having the reciprocal amount of square footage in the salon. A lot of living and socializing will be happening on the aft deck, so its an important space for us. The aft deck will also have a grill, and a hot/cold outdoor shower with a shower curtain. Ill add the shower and wash down hose fitting after shes at the launch site and I have the salon welded in place.
I was bumming. The problem I encountered was having the gun suck air caused the paint to dry before it hit the metal giving me this unacceptable texture. The paint was dry and would not lay down. The area is right by the steps leading to the transom door, so I wanted to fix it. Having never repaired paint, I decided to try a small area to see how I could make out. I mean the worst that could happen is I mess it up more and have to re paint the whole transom. Starting with 800 grit wet dry, I wet sanded a 8" x 8" spot, then used 1200 grit and finished with 1500 grit ( all wet sanding). The final step was to use some fine cut polish and a electric orbital polisher, and buff the test spot. I have to say the spot looks amazing. The paint texture is now perfectly flat, and the polish brought the paint to a mirror finish. I actually look like I knew what I was doing. While the transom has a good shine to it ( except for the bad spot Im trying to fix), my test spot now looks far superior to any other part of the transom.
Fixing the bad spot is now going to make the bad spot the best spot, so I think Ill end up polishing the whole transom to make everything look even. I dont want to get in to this habit for the rest of the hull, so Im content with polishing this area, as this is the only way on and off of the boat. Having a crappy finish on this area will bug me every time I pass by, so Im fixing it. I took a picture showing the messed up flat looking paint on the right side of the picture and the repaired shiny paint more on the left side. The key is not letting the paint pot get to low, and making sure you have enough thickness in case you need to do a repair.. Im not looking for a perfect mirror finish on the boat, but I want it to please me, be easy to clean, and be respectable in the eyes of those who know.
Im now ready to start work on painting the below the water line area of the hull, but before I do that I have to organize the shop. Under the boat has been used for storage of parts for the wheel house/salon, scrap metal, spare parts, scrap wood, and a host of all kinds of debris. I have a days worth of making things right, then I can start on prepping this part of the hull. Hopefully, within two weeks, the bottom of the hull is painted and Ill start getting the boat off of the building cradle. Before I can get axles under her, I have to have the cradle removed and have her sitting on blocks. In the last picture, you can see some of the below the water line paint I have already rolled on. Im using a two part paint called Amerlock. Pretty nasty stuff that is too thick to spray so Ill be rolling it on.
Cheers
.jpg)
0 komentar:
Posting Komentar